Over the weekend Lucy and I spent some time prepping her C33 Nissan Laurel for its first EVER drift day.

This wasn’t as difficult as you might think. There are far too many people who think that in order to start drifting you need a million horsepowers, Wisefab all of the things, a full competition spec roll cage and a super expensive LSD among other things. But the truth is you don’t. The only things you really need are:

  1. A bucket seat and harness to hold you in place, there’s nothing worse than trying to maintain control of your car while being thrown around in the seat.
  2. Some coilovers, you probably could use lowering springs but if you’re going to do it you may as well do it right the first time.
  3. A rear wheel drive car, you probably can “drift” your front wheel drive Corsa with the aid of some freshly liberated serving trays from your local Maccies (MacDonalds) but lets be honest, it’s not the same!
  4. A Welded diff.

The Laurel already had most of these things, even though the car came with coilovers already on it we decided to put some fresh HSD coilovers on. We’d already fitted a bucket seat and harness for the driver, the only thing that was missing was the welded diff. After quite a bit of searching we found one for sale on Facebook Marketplace and headed to deepest darkest Shildon to pick it up. We could have welded up the diff that was in the car but since its harder (if not impossible) to get an MOT on a welded diff we decided it would be best to keep the open diff as a spare.

Then the weekend came and it was time to fit it.

This was pretty done pretty much as you would do anything on the underside of a car on your driveway, first chock the front wheels to make sure the car can’t move and crush you, next jack the back of the car up as high as you can get it (in our case we had to take the front bumper off as the car has many lows!) finally secure your car in the air with some axle stands, I placed these under the front bolting points of the rear subframe, the main reason being to keep the car secure but still give me as much room for manoeuvre as possible.

Next we decided to remove the drivers side rear wheel this was just to give us more space to get under the car and move around.

Now that the car was in the air the first thing to do is loosen the bolts holding the driveshaft in place, to do this it helps if you have someone with you otherwise you’ll be getting out from under the car a lot! Get them to put the handbrake on, this helps to keep the shafts from spinning. Unfasten the driveshaft bolts that you can see on either side of the diff, and keep working around, getting your helper to take off and set the handbrake again as you move the shafts around to the next bolt.

Once you’ve got all of the bolts free you should be able to pop the driveshafts out with a bit of force and move them out of the way.

Next is the turn of the prop shaft, there were four bolts here this time we also put the car in gear to stop any movement while getting these unfastened, finally you just have the bolts holding your diff in place and its ready to come out.

Since I already had one I decided to use a transmission jack to take the weight of the diff while I manoeuvred it out of the car, this made it much easier but if you don’t have one you can use a trolley jack, just remember that it isn’t going to be as stable so keep a close eye on it.

Finally, came the fitting of the welded diff, and fitting is quite literally the reverse of the removal, Where possible we used some thread lock on the bolts to ensure they didn’t start working themselves free.

So now the Laurel, and Lucy are ready for their first drift outing!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s